The Audac ATEO4MK2/B is described as a black wall speaker with a 4-inch MF/LF woofer, a 1-inch dome tweeter and Audac’s CleverMount mounting system. Its supplied specifications list full-range operation, separate low-impedance and transformer-tap details, 130° horizontal and vertical dispersion, and options for vertical or horizontal mounting. These features make it a product to assess for a suitable installed-audio system, provided its exact electrical configuration and compatibility are confirmed.
Check the exact model first: The product title identifies the ATEO4MK2/B, while the supplied impedance entry is labelled “8 Ω (ATEO4)” and the colour entry refers to “Black (ATEO4/B).” These labels may refer to related variants, but the information provided does not confirm that every specification applies unchanged to the ATEO4MK2/B. Verify the exact model and its specifications before using them for amplifier selection or installation planning.
Driver configuration and response: The speaker is classified as full range and lists a 4-inch MF/LF woofer and a 1-inch dome tweeter. The supplied frequency response is 100 Hz–20 kHz within ±3 dB, with a wider stated range of 65 Hz–20 kHz at −10 dB. These two ranges use different tolerances and should not be treated as equivalent. They provide useful reference points for comparison, but do not describe the full response curve or predict exactly how the speaker will sound in a particular room.
A two-driver specification identifies the listed woofer and tweeter, but does not by itself describe the complete crossover design or acoustic performance. Room reflections, wall construction, speaker height, programme material and amplifier settings can all affect what listeners hear. If a project depends on a particular frequency response, tonal balance or sound level, ask for additional manufacturer information rather than drawing conclusions from the published ranges alone.
Power ratings and sound-pressure figures: The listing gives three distinct power-handling figures: 35 W RMS/AES, 70 W program and 140 W peak. Keep these ratings separate when discussing system matching. The 140 W peak rating is not a continuous-power rating and should not be substituted for the 35 W RMS/AES figure. The supplied information does not provide a recommended amplifier rating or limiter settings, so check compatibility with the amplifier documentation and the confirmed speaker configuration.
Sensitivity is listed as 86 dB at 1 W/1 m. Maximum sound-pressure values are given as 101 dB at 8 Ω and 100 dB at 100 V. The source field includes a “Max. W/1m” notation but does not explain the test method or reference conditions clearly. Treat the figures as supplied, and avoid comparing them directly with other products unless the measurement methods are known to match.
Dispersion and orientation: Horizontal and vertical dispersion are both listed as 130°. These values can help when considering speaker placement and the area listeners need to cover. They do not guarantee uniform coverage throughout a room or establish how many speakers are required. Room dimensions, wall surfaces, listener positions, mounting height and the direction the speaker faces all influence coverage.
The supplied inclination figures are 30° left, 30° right, 30° bottom and 5° top. The listing does not explain the reference point for these angles or how they relate to the mounting position. Treat them as supplied installation references, and confirm their interpretation in the mounting instructions. If the intended installation depends on a specific aiming angle, check that the CleverMount arrangement supports it before fixing the speaker in place.
CleverMount and mounting flexibility: CleverMount is identified as the speaker’s mounting system, and the product information describes it as patented. The supplied key features present the system as a way to support mounting in vertical or horizontal orientation. Confirm the mounting method, required clearance and any limitations for the chosen wall surface before installation. The listed accessories include an Allen-key wrench; no other mounting hardware is specified, so confirm exactly what is included.
The ability to mount horizontally or vertically may make the speaker easier to assess for different room layouts. The supplied feature list also says the logo can be rotated. This is an appearance and orientation detail, not a substitute for checking the mounting instructions or cable access. Plan the speaker’s position before installation so that its orientation, aiming, cable path and access for future adjustment suit the room.
Low-impedance and transformer-tap information: The key features describe both 100 V and low-impedance connection possibilities. The supplied impedance entry is 8 Ω for “ATEO4,” so confirm that the value applies to the ATEO4MK2/B variant. The transformer-tap information includes both 70 V and 100 V entries, but the correct connection depends on the specific installation and the manufacturer’s wiring instructions. Do not assume that all connection modes can be used simultaneously.
As supplied, the transformer table reads:
Confirm the table and terminal selection for the exact model. For a distributed speaker system, check that the amplifier’s line voltage, the selected tap and the total connected load are appropriate. For a low-impedance system, verify the stated impedance, amplifier output and wiring arrangement. Do not select an amplifier or tap based only on the 140 W peak figure.
Connector and wiring: The supplied connector specification is a 6-pin custom terminal block. This is a detail to confirm before planning cabling, especially when replacing a speaker or integrating it with an existing installation. The information does not provide a pin assignment, wiring diagram or confirmation of which cables or connectors are included. Ask for the correct connection instructions and use the terminals only in the configuration specified for the exact model.
The 6-pin connector specification does not establish that the speaker uses a standard plug, nor does it identify how each pin is assigned. Confirm which terminals correspond to the intended low-impedance or transformer-tap connection. If several speakers are being installed, plan the wiring consistently and have the total load checked. A connector that can be physically fitted is not, by itself, proof that the electrical configuration is correct.
Enclosure and appearance: The enclosure is specified as ABS, with a steel grille at the front. The /B version is listed in black. These construction and finish details help with matching the speaker to the wall and surrounding equipment. The supplied information does not give an IP rating or a weather-resistance specification, so the material and black finish should not be taken as evidence that the speaker is suitable for outdoor, wet or exposed installations.
The speaker measures 136 × 244 × 153 mm (W × H × D) and weighs 2.05 kg. These dimensions can help with clearance and placement planning. Confirm the mounting surface can support the installation and that the speaker will not obstruct nearby doors, screens, equipment or room features. The supplied information does not state the dimensions of every mounting component or the space needed to access the connector, so consult the installation instructions if clearance is tight.
Potential installation settings: The ATEO4MK2/B may be considered for offices, meeting rooms, reception areas, retail spaces, hospitality venues and other indoor locations where a wall-mounted speaker suits the audio design. These are possible applications, not a promise that a particular number of speakers will provide suitable coverage. Assess the room size, background noise, listening positions, mounting height and intended audio content. Check whether the response, sensitivity and power ratings match the requirements of the system.
For speech, consider whether the speaker’s position and aiming angle help listeners hear clearly across the room. For background music, consider the desired listening level and whether the listed response range suits the programme material. Larger, divided or acoustically challenging spaces may require more than one speaker or a different system design. The supplied data does not specify a recommended room size or speaker spacing, so plan for the actual site rather than relying on the dispersion figure alone.
Amplifier and system planning: The speaker is not described as having a built-in amplifier. Plan for a compatible external amplifier or audio system, and verify whether the installation will use low-impedance operation or a transformer tap. Confirm the exact variant’s impedance, line voltage and connection details before wiring. For a multi-speaker system, the total load and tap selections must be considered alongside the amplifier’s capabilities.
Do not interpret RMS/AES, program and peak ratings as interchangeable. For continuous system design, refer to the appropriate specification and amplifier guidance rather than treating the peak figure as the speaker’s normal operating rating. If the system uses 70 V or 100 V distribution, confirm the tap setting and total system load. If it uses a low-impedance output, verify the speaker and amplifier impedance requirements. Ask a qualified installer or the supplier to review a configuration if any of these details are uncertain.
Installation and commissioning: Before mounting, identify the correct ATEO4MK2/B instructions and verify the mounting surface, speaker orientation and cable route. Check the connector and terminal assignment, and confirm the selected electrical mode and tap. Secure the speaker using the specified CleverMount procedure and included or separately confirmed hardware. Do not infer mounting steps from the product name or assume the Allen key is the only item required for a particular wall type.
After installation, test the complete audio system at a moderate level. Check that the speaker operates correctly, that the sound reaches the intended listening positions and that there is no unexpected distortion. In a multi-speaker setup, compare the sound across the space and confirm all taps and connections are consistent with the system design. If the coverage is uneven, review speaker placement and aiming rather than simply increasing amplifier level.
Environmental suitability and warranty checks: The listed operating temperature range is −20°C to 60°C. No IP rating or moisture-protection specification was supplied. Do not assume the speaker is weatherproof or suitable for an outdoor or damp installation based on its operating temperature range. If environmental protection is important, request the applicable rating for the exact model.
No warranty term was included in the specifications supplied for this listing. Ask BME to confirm whether a warranty applies to the exact product and, if so, its issuer, coverage, eligibility and terms in Bangladesh. Also confirm the package contents, especially the mounting hardware and terminal connection details. These checks are useful before choosing a speaker for an installed system that may be difficult to access after the wall mounting is complete.
Overall, the Audac ATEO4MK2/B combines a two-driver description, CleverMount mounting, broad dispersion figures and low-impedance and transformer-tap information. It may suit a compatible wall-speaker installation once the exact model, connection configuration and mounting requirements have been confirmed. The most important checks are whether the listed 8 Ω specification applies to the MK2/B, which terminals and taps to use, and whether the wall and room layout suit the proposed installation.
✅ Key Features
✅ Usage / Applications
✅ Benefits of This Product?
✅ Ideal For
The Audac ATEO4MK2/B is ideal for buyers planning a wall-mounted speaker installation who need a compact two-driver design with listed low-impedance and transformer-tap details. It may suit meeting rooms, offices, reception areas, retail spaces and other indoor locations where a wall-mounted speaker matches the layout. The 130° horizontal and vertical dispersion figures and the option to mount vertically or horizontally can help inform initial placement planning.
It is best suited to purchasers who can verify the exact model and electrical configuration before connecting it. The supplied impedance entry refers to ATEO4 rather than explicitly to ATEO4MK2/B, while the transformer table lists 70 V and 100 V taps. Confirm the applicable settings and the 6-pin terminal assignment with BME or the product documentation. No IP rating was supplied, so do not assume outdoor or weatherproof suitability. Confirm mounting requirements and warranty terms before ordering.
✅ Why Choose the Audac ATEO4MK2/B Wall Speaker with 4-inch CleverMount - Black?
The ATEO4MK2/B is worth considering when you want a wall-mounted speaker with a defined driver configuration and a mounting system designed for installed audio. The listing specifies a 4-inch MF/LF woofer and a 1-inch dome tweeter, a response of 100 Hz–20 kHz within ±3 dB and an extended range of 65 Hz–20 kHz at −10 dB. The 130° horizontal and vertical dispersion figures provide useful reference points for discussing placement, although the room still needs to be assessed on its own.
CleverMount is a prominent part of the supplied product information, along with the ability to mount vertically or horizontally and rotate the logo. The ABS enclosure, steel grille, black finish and 2.05 kg weight are also practical details for considering appearance and wall installation. Low-impedance and transformer-tap connection options are listed, so the speaker can be evaluated against different system designs once the exact configuration is confirmed.
That confirmation matters: the impedance entry is marked for ATEO4, while the title specifies ATEO4MK2/B. The connector is a 6-pin custom terminal block, and the supplied tap table has distinct 70 V and 100 V values. Confirm which specifications apply to the exact variant, the terminal assignments and the selected system mode before connecting the speaker. If those details match your project, it is a considered option for a compatible wall-audio installation.
✅ Why Buy This Product from BME?
For buyers in Bangladesh, contact BME to enquire about the Audac ATEO4MK2/B and confirm current product and purchase details. No current price or availability is stated here, so ask BME for a quote and the terms applicable to your order. Confirm any delivery or collection arrangements directly rather than assuming they are available.
Use your enquiry to verify that the product offered is the exact ATEO4MK2/B variant. The supplied specifications include entries labelled ATEO4 and ATEO4/B, so ask which impedance and colour details apply to the MK2/B model. You can also confirm the 6-pin terminal assignment, the transformer tap settings, the appropriate connection mode and which mounting items are included.
No warranty term was included in the specifications supplied for this listing. Ask BME to confirm whether a warranty applies, and if so, its issuer, coverage, eligibility and Bangladesh terms. These checks can help you compare the exact speaker with your amplifier, wiring and wall layout without relying on assumptions about compatibility or package contents.
✅ Buying Guide
✅ Customers Ask About / Frequently Asked Questions
Q: What is the Audac ATEO4MK2/B price in Bangladesh?
A: Contact BME for the current quote and purchase terms.
Q: Is this the ATEO4MK2/B model?
A: That is the product title, but some supplied specification entries refer to ATEO4 or ATEO4/B. Confirm the exact model and applicable specifications with BME.
Q: What drivers are listed?
A: The supplied information lists a 4-inch MF/LF woofer and a 1-inch dome tweeter.
Q: Is it an 8 Ω speaker?
A: An 8 Ω impedance is listed for ATEO4. Confirm that it applies to the ATEO4MK2/B variant before connecting it.
Q: Can it be used on a 70 V or 100 V system?
A: The supplied transformer table includes 70 V and 100 V tap entries. Confirm the correct tap and wiring for the exact model and amplifier.
Q: What are its power ratings?
A: The listed ratings are 35 W RMS/AES, 70 W program and 140 W peak. They are separate ratings and should not be treated as interchangeable.
Q: What connector does it use?
A: A 6-pin custom terminal block is specified. Ask for the pin assignment and connection instructions.
Q: Can it be mounted horizontally or vertically?
A: The supplied key features describe both orientations and a rotatable logo. Confirm the permitted mounting and aiming positions.
Q: Is the speaker suitable for outdoor use?
A: No IP rating or weather-resistance specification was supplied. Do not assume it is suitable for outdoor or damp locations.
Q: What warranty is included?
A: No warranty term was supplied for this listing. Ask BME to confirm whether a warranty applies and what its terms are.
Q: What accessories are included?
A: An Allen-key wrench is listed. Confirm whether any additional mounting hardware or accessories are included with the unit offered.
✅ Why Buy This Product
Consider the Audac ATEO4MK2/B if you need a wall-mounted speaker with a 4-inch MF/LF woofer, a 1-inch dome tweeter and CleverMount mounting. Its vertical and horizontal mounting options, 130° dispersion figures, black finish and listed transformer taps provide useful details for planning a compatible installed-audio system.
Before choosing it, confirm the exact model variant, whether the 8 Ω specification applies, and the correct use of the 70 V or 100 V taps. Check the custom terminal-block wiring, wall mounting requirements and environmental suitability; no IP rating was supplied. Ask BME to clarify package contents and any applicable warranty terms. If the confirmed model and configuration suit your project, contact BME to discuss the ATEO4MK2/B for your installation.
Have question about this product? Get specific details about this product from expert.